=back
+=head2 Plugin C<irq>
+
+=over 4
+
+=item B<Irq> I<Irq>
+
+Select this irq. By default these irqs will then be collected. For a more
+detailed description see B<IgnoreSelected> below.
+
+=item B<IgnoreSelected> I<true>|I<false>
+
+If no configuration if given, the B<irq>-plugin will collect data from all
+irqs. This may not be practical, especially if no interrupts happen. Thus, you
+can use the B<Irq>-option to pick the interupt you're interested in.
+Sometimes, however, it's easier/prefered to collect all interupts I<except> a
+few ones. This option enables you to do that: By setting B<IgnoreSelected> to
+I<true> the effect of B<Irq> is inversed: All selected interupts are ignored
+and all other interupts are collected.
+
+=back
+
=head2 Plugin C<mbmon>
=over 4
=over 4
+=item B<CacheFlush> I<Seconds>
+
+When the C<rrdtool plugin> uses a cache (by setting B<CacheTimeout>, see below)
+it writes all values for a certain RRD-file if the oldest value is older than
+(or equal to) the number of seconds specified. If some RRD-file is not updated
+anymore for some reason (the computer was shut down, the network is broken,
+etc.) some values may still be in the cache. If B<CacheFlush> is set, then the
+entire cache is searched for entries older than B<CacheTimeout> seconds and
+written to disk every I<Seconds> seconds. Since this is kind of expensive and
+does nothing under normal circumstances, this value should not be too small.
+900 seconds might be a good value, though setting this to 7200 seconds doesn't
+normally do much harm either.
+
=item B<CacheTimeout> I<Seconds>
-If this option is set to a value greater than zero, the C<rrdtool>-plugin will
-write values every I<Seconds> seconds to the RRD-files. Writing multiple values
-at once reduces IO-operations and thus lessens the load produced by updating
-the files. The tradeoff is that the graphs kind of "drag behind" and that more
-memory is used.
+If this option is set to a value greater than zero, the C<rrdtool plugin> will
+save values in a cache, as described above. Writing multiple values at once
+reduces IO-operations and thus lessens the load produced by updating the files.
+The tradeoff is that the graphs kind of "drag behind" and that more memory is
+used.
+
+=item B<DataDir> I<Directory>
+
+Set the directory to store RRD-files under. Per default RRD-files are generated
+beneath the daemon's working directory, i.E<nbsp>e. the B<BaseDir>.
=back
=over 4
-=item B<ExtendedSensorNaming> I<true>|I<false>
-
-If set to I<true> this option switches on the extended sensors and RRD-files
-naming. This option exists to preserve backwards compatibility. It is
-recommended that you set this option to I<true>. The default is I<false> to
-maintain compatibility only.
-
-Sensors get names like I<chip-bus-address/type-feature> (e.g.
-I<it8712-isa-0290/voltage-in1>) and RRD files are therefore stored in a
-standalone directory inside the B<DataDir> directory and get names like
-I<lm_sensors-chip-bus-address/type-feature.rrd> (e.g.
-I<lm_sensors-it8712-isa-0290/voltage-in1.rrd>).
-
-The B<ExtendedSensorNaming> option breaks the compatibility with previous
-sensors and RRD files naming and the place where RRDs are stored. If you turn
-it on, the plugin will create new RRD files in a standalone directory inside
-the B<DataDir> directory and without previous history. You can rename ``old''
-RRD-files to preserve already collected statistics, because the file layout
-hasn't changed. If you have two chips of the same type, you need to use
-B<ExtendedSensorNaming> in order to collect information from both chips.
-
-If not set or set to I<false>, the extended naming is not active. Sensors get
-names like I<chip-feature> (e.g. I<it8712-in1>) and RRD files are stored in the
-main B<DataDir> directory and get names like I<sensors-chip-feature.rrd> (e.g.
-I<sensors-it8712-in1.rrd>). You simply continue using the plugin the old way
-and additionally also getting data for newly added sensors in this mode.
-
-=item B<Sensor> I<chip-feature> or B<Sensor> I<chip-bus-address/type-feature>
-
-Both option modes select the name of the sensor which you want to collect.
-The naming scheme is dependent on the state of the B<ExtendedSensorNaming>
-option (see previous option). Both option modes can also deselect the
-sensor according to the B<IgnoreSelected> option (see below).
-
-For example the option "B<Sensor> I<it8712-in1>" will cause the collectd
-to gather data for the voltage sensor I<in1> of the I<it8712> chip in case
-of the B<ExtendedSensorNaming> option is set to I<false>.
-
-And likewise the option "B<Sensor> I<it8712-isa-0290/voltage-in1>" will
-cause the collectd to gather data for the voltage sensor I<in1> of the I<it8712>
-on the isa bus at the address 0290 in case of the B<ExtendedSensorNaming>
-option set to I<true>.
+=item B<Sensor> I<chip-bus-address/type-feature>
-=item B<IgnoreSelected> I<true>|I<false>
+Selects the name of the sensor which you want to collect or ignore, depending
+on the B<IgnoreSelected> below. For example, the option "B<Sensor>
+I<it8712-isa-0290/voltage-in1>" will cause collectd to gather data for the
+voltage sensor I<in1> of the I<it8712> on the isa bus at the address 0290.
-If no configuration if given, the B<sensors>-plugin will collect data from
-all sensors. This may not be practical, especially for uninteresting sensors.
-Thus, you can use the B<Sensor>-option to pick the sensors you're
-interested in. Sometimes, however, it's easier/prefered to collect all
-sensors I<except> a few ones. This option enables you to
-do that: By setting B<IgnoreSelected> to I<true> the effect of
-B<Sensor> is inversed: All selected sensors are ignored and all
-other sensors are collected.
+=item B<IgnoreSelected> I<true>|I<false>
-back
+If no configuration if given, the B<sensors>-plugin will collect data from all
+sensors. This may not be practical, especially for uninteresting sensors.
+Thus, you can use the B<Sensor>-option to pick the sensors you're interested
+in. Sometimes, however, it's easier/prefered to collect all sensors I<except> a
+few ones. This option enables you to do that: By setting B<IgnoreSelected> to
+I<true> the effect of B<Sensor> is inversed: All selected sensors are ignored
+and all other sensors are collected.
=back
projects / collectd.git / blobdiff