# StoreRates false
# GraphitePrefix "collectd."
# GraphiteEscapeChar "_"
+ # GraphiteSeparateInstances false
+ # GraphiteAlwaysAppendDS false
</Publish>
# Receive values from an AMQP broker
metric parts (host, plugin, type).
Default is "_" (I<Underscore>).
+=item B<GraphiteSeparateInstances> B<true>|B<false>
+
+If set to B<true>, the plugin instance and type instance will be in their own
+path component, for example C<host.cpu.0.cpu.idle>. If set to B<false> (the
+default), the plugin and plugin instance (and likewise the type and type
+instance) are put into one component, for example C<host.cpu-0.cpu-idle>.
+
+=item B<GraphiteAlwaysAppendDS> B<true>|B<false>
+
+If set to B<true>, append the name of the I<Data Source> (DS) to the "metric"
+identifier. If set to B<false> (the default), this is only done when there is
+more than one DS.
+
=back
=head2 Plugin C<apache>
=back
+=head2 Plugin C<barometer>
+
+This plugin reads absolute air pressure using digital barometer sensor MPL115A2
+or MPL3115 from Freescale (sensor attached to any I2C bus available in
+the computer, for HW details see
+I<http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MPL115A> or
+I<http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MPL3115A2>).
+The sensor type - one fo these two - is detected automatically by the plugin
+and indicated in the plugin_instance (typically you will see subdirectory
+"barometer-mpl115" or "barometer-mpl3115").
+
+The plugin provides absolute barometric pressure, air pressure reduced to sea
+level (several possible approximations) and as an auxiliary value also internal
+sensor temperature. It uses (expects/provides) typical metric units - pressure
+in [hPa], temperature in [C], altitude in [m].
+
+It was developed and tested under Linux only. The only platform dependency is
+the standard Linux i2c-dev interface (the particular bus driver has to
+support the SM Bus command subset).
+
+The reduction or normalization to mean sea level pressure requires (depedning on
+selected method/approximation) also altitude and reference to temperature sensor(s).
+When multiple temperature sensors are configured the minumum of their values is
+always used (expecting that the warmer ones are affected by e.g. direct sun light
+at that moment).
+
+Synopsis:
+
+ <Plugin "barometer">
+ Device "/dev/i2c-0";
+ Oversampling 512
+ PressureOffset 0.0
+ TemperatureOffset 0.0
+ Normalization 2
+ Altitude 238.0
+ TemperatureSensor "myserver/onewire-F10FCA000800/temperature"
+ </Plugin>
+
+=over 4
+
+=item B<Device> I<device>
+
+Device name of the I2C bus to which the sensor is connected. Note that typically
+you need to have loaded the i2c-dev module.
+Using i2c-tools you can check/list i2c buses available on your system by:
+
+ i2cdetect -l
+
+Then you can scan for devices on given bus. E.g. to scan the whole bus 0 use:
+
+ i2cdetect -y -a 0
+
+This way you should be able to verify that the pressure sensor (either type) is
+connected and detected on address 0x60.
+
+=item B<Oversampling> I<value>
+
+For MPL115 this is the size of the averaging window. To filter out sensor noise
+a simple averaging using floating window of configurable size is used. The plugin
+will use average of the last C<value> measurements (value of 1 means no averaging).
+Minimal size is 1, maximal 1024.
+
+For MPL3115 this is the oversampling value. The actual oversampling is performed
+by the sensor and the higher value the higher accuracy and longer conversion time
+(although nothing to worry about in the collectd context). Supported values are:
+1, 2, 4, 8, 16, 32, 64 and 128. Any other value is adjusted by the plugin to
+the closest supported one. Default is 128.
+
+=item B<PressureOffset> I<offset>
+
+You can further calibrate the sensor by supplying pressure and/or temperature offsets.
+This is added to the measured/caclulated value (i.e. if the measured value is too high
+then use negative offset).
+In hPa, default is 0.0.
+
+=item B<TemperatureOffset> I<offset>
+
+You can further calibrate the sensor by supplying pressure and/or temperature offsets.
+This is added to the measured/caclulated value (i.e. if the measured value is too high
+then use negative offset).
+In C, default is 0.0.
+
+=item B<Normalization> I<method>
+
+Normalization method - what approximation/model is used to compute mean sea
+level pressure from the air absolute pressure.
+
+Supported values of the C<method> (integer between from 0 to 2) are:
+
+=over 5
+
+=item B<0> - no conversion, absolute pressrure is simply copied over. For this method you
+ do not need to configure C<Altitude> or C<TemperatureSensor>.
+
+=item B<1> - international formula for conversion ,
+See I<http://en.wikipedia.org/wiki/Atmospheric_pressure#Altitude_atmospheric_pressure_variation>.
+For this method you have to configure C<Altitude> but do not need C<TemperatureSensor>
+(uses fixed global temperature average instead).
+
+=item B<2> - formula as recommended by the Deutsche Wetterdienst (German
+Meteorological Service).
+See I<http://de.wikipedia.org/wiki/Barometrische_H%C3%B6henformel#Theorie>
+For this method you have to configure both C<Altitude> and C<TemperatureSensor>.
+
+=back
+
+
+=item B<Altitude> I<altitude>
+
+The altitude (in meters) of the location where you meassure the pressure.
+
+=item B<TemperatureSensor> I<reference>
+
+Temperature sensor which should be used as a reference when normalizing the pressure.
+When specified more sensors a minumum is found and uses each time.
+The temperature reading directly from this pressure sensor/plugin
+is typically not suitable as the pressure sensor
+will be probably inside while we want outside temperature.
+The collectd reference name is something like
+<hostname>/<plugin_name>-<plugin_instance>/<type>-<type_instance>
+(<type_instance> is usually omitted when there is just single value type).
+Or you can figure it out from the path of the output data files.
+
+=back
+
=head2 Plugin C<bind>
Starting with BIND 9.5.0, the most widely used DNS server software provides
Sets the plugin instance to I<Instance>.
+=item B<Interval> I<Interval>
+
+Sets the interval (in seconds) in which the values will be collected from this
+URL. By default the global B<Interval> setting will be used.
+
=item B<User> I<Name>
=item B<Password> I<Password>
=back
-+=head2 Plugin C<load>
+=head2 Plugin C<load>
The I<Load plugin> collects the system load. These numbers give a rough overview
over the utilization of a machine. The system load is defined as the number of
Otherwise, use the B<Port> option above. See the documentation for the
C<mysql_real_connect> function for details.
+=item B<InnodbStats> I<true|false>
+
+If enabled, metrics about the InnoDB storage engine are collected.
+Disabled by default.
+
=item B<MasterStats> I<true|false>
=item B<SlaveStats> I<true|false>
Specify whether to use an SSL connection when contacting the server. The
following modes are supported:
-=item B<Instance> I<name>
-
-Specify the plugin instance name that should be used instead of the database
-name (which is the default, if this option has not been specified). This
-allows to query multiple databases of the same name on the same host (e.g.
-when running multiple database server versions in parallel).
-
=over 4
=item I<disable>
=back
+=item B<Instance> I<name>
+
+Specify the plugin instance name that should be used instead of the database
+name (which is the default, if this option has not been specified). This
+allows to query multiple databases of the same name on the same host (e.g.
+when running multiple database server versions in parallel).
+
=item B<KRBSrvName> I<kerberos_service_name>
Specify the Kerberos service name to use when authenticating with Kerberos 5
=item B<AlwaysAppendDS> B<false>|B<true>
+If set to B<true>, append the name of the I<Data Source> (DS) to the "metric"
+identifier. If set to B<false> (the default), this is only done when there is
+more than one DS.
+
+=back
+
+=head2 Plugin C<write_tsdb>
+
+The C<write_tsdb> plugin writes data to I<OpenTSDB>, a scalable open-source
+time series database. The plugin connects to a I<TSD>, a masterless, no shared
+state daemon that ingests metrics and stores them in HBase. The plugin uses
+I<TCP> over the "line based" protocol with a default port 4242. The data will
+be sent in blocks of at most 1428 bytes to minimize the number of network
+packets.
+
+Synopsis:
+
+ <Plugin write_tsdb>
+ <Node "example">
+ Host "tsd-1.my.domain"
+ Port "4242"
+ HostTags "status=production"
+ </Node>
+ </Plugin>
+
+The configuration consists of one or more E<lt>B<Node>E<nbsp>I<Name>E<gt>
+blocks. Inside the B<Node> blocks, the following options are recognized:
+
+=over 4
+
+=item B<Host> I<Address>
+
+Hostname or address to connect to. Defaults to C<localhost>.
+
+=item B<Port> I<Service>
+
+Service name or port number to connect to. Defaults to C<4242>.
+
+
+=item B<HostTags> I<String>
+
+When set, I<HostTags> is added to the end of the metric. It is intended to be
+used for name=value pairs that the TSD will tag the metric with. Dots and
+whitespace are I<not> escaped in this string.
+
+=item B<StoreRates> B<false>|B<true>
+
+If set to B<true>, convert counter values to rates. If set to B<false>
+(the default) counter values are stored as is, as an increasing
+integer number.
+
+=item B<AlwaysAppendDS> B<false>|B<true>
+
If set the B<true>, append the name of the I<Data Source> (DS) to the "metric"
identifier. If set to B<false> (the default), this is only done when there is
more than one DS.
=item B<Plugin> I<Name>
Name of the write plugin to which the data should be sent. This option may be
-given multiple times to send the data to more than one write plugin.
+given multiple times to send the data to more than one write plugin. If the
+plugin supports multiple instances, the plugin's instance(s) must also be
+specified.
=back
If no plugin is explicitly specified, the values will be sent to all available
write plugins.
-Example:
+Single-instance plugin example:
<Target "write">
Plugin "rrdtool"
</Target>
+Multi-instance plugin example:
+
+ <Plugin "write_graphite">
+ <Node "foo">
+ ...
+ </Node>
+ <Node "bar">
+ ...
+ </Node>
+ </Plugin>
+ ...
+ <Target "write">
+ Plugin "write_graphite/foo"
+ </Target>
+
=item B<jump>
Starts processing the rules of another chain, see L<"Flow control"> above. If
projects / collectd.git / blobdiff